Firewall work: 1 hour

• Installed brake reservoir mount. AN fittings and an aluminum tube will connect this to the bulkhead fitting after the forward fuselage structure is installed.
• Installed alternator fuses and hardware.
• I also started on cutting up some 1/16" rubber sheeting that will be glued into the battery boxes to give a little padding.

Firewall progress:

Finished firewall doubler riveting: 4 hours

• Finished riveting all doublers to firewall
• Mounted all ANL fuse holders
• Mounted "forest of tabs" ground bus
• Prepared battery and start contactors for mounting. Mounting bolts on order.

Contactors ready to be installed:

All firewall doublers in place:

Forest of tabs ground bus:

Riveting in progress: (used large piece of rivet tape to protect paint)

Alternator fuses and insulated bus bar:

More firewall and forward fuselage: 8 hours

The following items were done over several days-

• Finished painting firewall doublers and battery boxes
• Opened up all holes on forward top skin for cherry max rivets
• I decided to add a anl fuse for the main VPX power feed so I made another doubler and drilled it to the firewall. I also made a copper bus bar to connect it.
• I started riveting the doublers to the firewall. I started with the fuse holder doubler for the alternators.
• I removed the forward top skin and support structure. I also located where I will mount the manifold pressure sensors for the electronic ignition.

Finishing up the painting:

Forward top skin drilled:

Locating the fuse holder for the main power feed:

Drilling main power feed doubler:

Checking fit with bus bar:

Alternator fuse holder doubler riveted on:

Locating manifold pressure sensor mounting location:

Forward top skin: 3 hours

• Removed forward top skin and used old forward top skin to drill mounting holes for defog fans and transfer the cut out pattern for the fans.
• Deburred and dimpled forward top skin and sub-panel
• Re-attached forward skin - ready to be reamed for the Cherrymax NAS rivets.

Forward skin ready for next stage:

Edge finishing and deburring:

Firewall forward and forward top skin 2.0: 6 hours

• Prepped, primed and painted battery boxes and some aluminum spacers for the firewall and a previously installed doubler
• Curved fuselage forward top skin with large piece of pvc pipe. I taped the edge of the skin to the pipe and rolled it on the work bench. I also held the pipe inboard from the edge and put a little more curve in. It turned out great.
• I also put a "strong" edge roll on each side of the skin where it will attach to the longerons.
• All the above paid off. The skin now fits very well and is very tight but did not require any thing beyond a few wing nut clecos (in addition to standard clecos) to get it in place.
• I did the initial drilling of the new skin to the forward fuselage ribs and sub panel.
• I also received a new gadget ... The Grove Aircraft Acrovalve. This is a check valve vent for the brake reservoir so if you are doing aerobatics you won't spill brake fluid in the engine compartment.

Grove Acrovalve on brake reservoir, old vent fitting to right:

Very happy with fit on the 2.0 skin:

The wing nut clecos were helpful in several spots:

After curving the skin with the large PVC pipe:

Reading to paint the battery boxes:

Ready to paint a doubler I installed some time ago:

Finished making firewall doublers: 3 hours

• Fabricated the doublers for the brake fluid reservoir
• Deburred and cleaned firewall
• Prepped and primed doublers

Prepping doublers and battery boxes for priming:

Drilling brake reservoir doubler to firewall:

More firewall doublers: 4.5 hours

• Fitted left battery doubler plates. After reviewing fit with engine firewall recess. I decided to modify the doubler plates and mount the battery directly over the firewall recess with a washer for a spacer.
• Drilled firewall recess panel and firewall for various plate nuts
• Drilled right battery box to firewall
• Fabricated lower and upper right battery doublers
• Upper battery doubler also supports the brake reservoir fitting and the other ground bus bolt.

Drilling upper right battery doubler:

Drilling right battery box to firewall: